Where Can You Find a 240V or Three-Phase Stationary Concrete Pump?
By PumpX Team ·
Not every pump runs on a diesel engine. Electric stationary concrete pumps are used in factories, precast yards, tunnels, basements and anywhere that exhaust fumes or noise are a problem. If you are searching for a 240V or three-phase unit, here is how to think about it and where to look.
What is a stationary concrete pump?
A stationary pump (sometimes called a static or trailer-mounted pump) sits in one place while concrete is fed into the hopper and pushed through a pipeline. It can be powered by a diesel engine or an electric motor driving the hydraulic pump. Electric models plug into site power instead.
240V single-phase versus three-phase
| Feature | Single-phase 240V | Three-phase |
|---|---|---|
| Typical power | Lower | Higher |
| Output capacity | Generally limited | Usually larger |
| Supply needed | Standard outlet or small circuit | Industrial three-phase supply |
| Best for | Small, light-duty work, grouting, screed | Higher-volume placing |
| Availability | Fewer concrete-specific options | More common |
Voltages and phases differ between countries. For example, supply standards in Australia, North America and Europe are not the same, so confirm the motor's voltage, frequency and phase against your site supply. Never assume that a pump from overseas will run on your power without checking.
Do the power sums first
Before choosing a model, find out:
- Available supply: what voltage, phase and amperage does your site actually provide?
- Motor size: the pump's electric motor will need a supply that can handle the starting load. Ask the manufacturer for full-load current and recommended breaker and cable sizes.
- Cable length: long extension leads cause voltage drop.
- Generator option: if mains power is limited, a correctly sized generator may be needed. Ask an electrician.
Have a licensed electrician check the connection. Electricity near wet concrete is a serious hazard.
What are you pumping?
The word "concrete pump" covers a wide range of machines:
- Concrete line pumps for structural concrete and slabs.
- Grout pumps for fine mixes and injection work.
- Screed pumps for floor screeds.
- Shotcrete machines for sprayed concrete.
A pump built for grout will not shift 20mm aggregate concrete. Define your mix, aggregate size, required output per hour, and pumping distance and height before shopping. Compare machines on the machine specs pages to see typical output and pressure figures.
Where to find electric stationary pumps
- Pump manufacturers and dealers: ask for electric or "e-drive" stationary models and whether they have local agents.
- Specialist grout and screed pump suppliers: often stock smaller electric units.
- Used equipment listings: browse pumps for sale on PumpX and filter for stationary models.
- Precast and ready-mix suppliers: they may know of equipment that comes up for sale.
- Local operators: ask in the concrete pumping directory; some may hire or sell electric units.
If a one-off job is the aim, hiring may make more sense than buying. Contact operators in the operator directory to ask what they can supply.
Buying checklist
- Confirm voltage, phase, frequency and amperage.
- Check output (cubic metres per hour) and maximum pressure against your needs.
- Inspect the pumping end and hydraulics for wear.
- Confirm parts and service support in your region.
- Ask for service records and, if possible, a test run.
- Verify safety features such as guards, emergency stops and hopper grates.
- Check any compliance or electrical certification your region requires.
Why choose electric?
- Lower noise and no exhaust fumes, which suits enclosed or sensitive sites.
- Fewer engine maintenance items.
- Can be cheaper to run where mains power is available.
The limits
- Dependent on a reliable power supply.
- Cables are a trip and damage hazard on busy sites.
- Typically less portable than a self-contained diesel unit.
- Fewer models to choose from.
Key takeaways
- Match the pump to your supply (voltage, phase and amperage) before shopping.
- 240V units are generally smaller; three-phase handles more volume.
- Define mix, output and distance first; grout pumps and concrete pumps differ.
- Use a licensed electrician and keep power away from wet areas.
- Source via dealers, specialist suppliers and used listings, or hire for one-offs.
Searching for a specific pump? Browse listings and connect with sellers on PumpX.
Original question on Reddit: r/manufacturing: Seeking a 240V or 3-phase stationary concrete pump